Electric Automation Forum
Forum » General Discussion

General Discussion

Everything about electric automation industries, like motor control, motion control, industrial communication, software etc, and the newest technologies around the world.
Post New Thread
Title/Thread
Last post by
Replacement of DC drive
Started by Zaid Alsayed,10-21-2013 04:51 AM
Replies: 6
Views: 2586
Roberto Carnelli
10-21-2013 09:06 PM
Polarization Index test
Started by Jerry Kurniawan,10-18-2013 04:52 AM
Replies: 1
Views: 1897
Christian Chinedu
10-20-2013 11:11 PM
Connecting to feeder conductors to Emergency generator
Started by Enid C.,10-18-2013 02:03 AM
Replies: 3
Views: 1361
Christian Chinedu
10-20-2013 11:11 PM
Determine power factor of generator(s)?
Started by Peter Chanel Kubebatu,10-18-2013 12:06 AM
Replies: 5
Views: 1709
Ing. Ole Knudsen
10-18-2013 12:41 PM
How to properly test directional relays?
Started by Simon Marley,10-18-2013 03:35 AM
Replies: 2
Views: 1766
Simon Marley
10-18-2013 08:45 AM
Simulation and Modelling, who uses it, and for what?
Started by Mothibi Thabeng,10-17-2013 09:22 PM
Replies: 4
Views: 2077
Mothibi Thabeng
10-18-2013 06:37 AM
Piezo electric motor or Ultrasonic motor
Started by Madhan Raj,10-17-2013 10:45 PM
Replies: 0
Views: 1444
Madhan Raj
10-17-2013 10:45 PM
Replies: 10
Views: 8838
Tony Stewart
10-17-2013 08:12 PM
How good are analogue hall sensors as a form of position control?
Started by Mark Gibbons,10-17-2013 08:39 AM
Replies: 4
Views: 1363
Mark Gibbons
10-17-2013 06:41 PM
Choosing a Power Supply for Your Stepper Drive
Started by Warren Osak,10-17-2013 09:42 AM
Replies: 3
Views: 1460
guna seelan
10-17-2013 04:35 PM
Replies: 4
Views: 1443
Bob Gudgel
10-17-2013 12:22 PM
Anyone knows PMSM with sernsorless control?
Started by Iris Y(HNC AUTOMATION),10-17-2013 12:46 AM
Replies: 1
Views: 1466
sivasubramanian narayanasami
10-17-2013 02:57 AM
Electrical Machine design Using MATLAB
Started by Uchit Sharma,10-15-2013 09:53 PM
Replies: 9
Views: 4105
sivasubramanian narayanasami
10-16-2013 08:26 PM
WHAT REAL TIME MOTION CONTROL SYSTEM DO YOU USE?
Started by Fernando Pons Ucles,10-14-2013 05:33 AM
Replies: 9
Views: 2621
Jan Bosteels
10-15-2013 04:29 AM
What is the most cost effective way of cutting lamination
Started by Nenad Mijatovic,10-13-2013 10:39 PM
Replies: 10
Views: 3526
Harri Vihriälä
10-14-2013 10:03 PM
Design Implications in Sub Micron Positioning
Started by Amy Butler,10-14-2013 12:55 AM
Replies: 7
Views: 1522
Raghavendra D.R.
10-14-2013 06:15 PM
1 << 16 17 18 19 20 >> 28